Baumer EAM MT Series Скачать руководство пользователя страница 13

Страница: 13 / 28

Baumer_EAM580_360_CANopen_MA_EN_Rev0003.0000h_Index0004.docx

Baumer Electric AG

06.08.2018

13/28

Frauenfeld, Switzerland

7 PDO Service

7.1

General

The device supports TPDO1 and TPDO2. PDOs are only transmitted in NMT operational mode.

7.2

PDO transmission types

The following transmission types are supported (object 180xh-2):



Synchronous transmission (1-240)



Asynchronous transmission (255)



Manufacturer transmission (254)



RTR-only transmission, event-driven (253)

Both PDOs support all transmission types.

Transmission type 253:

The PDO is only transmitted on request (remote transmission request).

Transmission type 255 and 254: The PDO is transmitted timer driven. The time interval between 2 PDOs can be

adapted in the object 180xh-5

Transmission type 1-240:

The PDO is transmitted after the n-th sync frame.

Transmission type 1:

The PDO is transmitted after one sync frame.

Transmission type 2:

The PDO is transmitted after two sync frames.

etc.

7.3

COB-ID

The COB-ID for both PDOs is changeable (in Object 180xh-1)

Default Values are:

TPDO1: 180h + node ID

TPDO2: 280h + node ID

Changes will be applied immediately.

The COB-ID is stored internally as a difference to the default COB-ID. Example:

Node ID: 1

COB-ID TPDO1: 181h

(Default value)

COB-ID TPDO1: 187h

(Changed by user)

Node ID: 9

COB-ID TPDO1: 189h

(Adapted automatic)

7.4

PDO mapping

The encoder supports dynamic mapping.

7.4.1

Mappable objects

The following objects are mappable:

Mapping content

Mapping entry

Description

Position encoder

0x60040020

Object 6004h Subindex 00h, data length 32 Bit

Speed encoder

0x60300120

Object 6030h Subindex 01h, data length 32 Bit

Alarms

0x65030010

Object 6503h Subindex 00h, data length 16 Bit

Warnings

0x65050010

Object 6505h Subindex 00h, data length 16 Bit

Diagnostic

0x21170010

Object 2117h Subindex 00h, data length 16 Bit

Speed [rpm]

0x21180010

Object 2118h Subindex 00h, data length 16 Bit

Time Stamp

0x21200010

Object 2120h Subindex 00h, data length 16 Bit

To change PDO mapping, disabling the mapping by writing 0 to 0x1A0x-0 is required first. Write the desired mapping

entry and enable the mapping again by writing the number of PDO contents to 0x1A0x-0.

Содержание EAM MT Series





























Результаты поиска

Содержание EAM MT Series

Отзывы:

Похожие инструкции для EAM MT Series

Бренды по названию

Популярные бренды

Baumer EAM MT Series, Руководство пользователя

Результаты поиска

Содержание EAM MT Series

Отзывы:

Похожие инструкции для EAM MT Series

Бренды по названию

Популярные бренды