manualshive.com logo in svg

Baumer 11233538, Руководство по эксплуатации, Страница: 10 / 54

Поделиться
Скачать
Baumer 11233538 Скачать руководство пользователя страница 10

3

 | 

Description

Baumer

10

Operating Manual

OM20/ OM30 RS485 with Modbus RTU | V1

3.3

Measurement field

INFO

The data for your sensor version can be found in the data sheet.

CD

MR

Sdc

Sde

ZP

ZP

Zero position

CD

Blind region

Sdc

Start of the measurement range

MR

Measurement range

Sde

End of the measurement range

Blind region (CD)

n

Region in which the sensor cannot detect any measurement objects.

n

Unwanted objects (objects not to be measured) in this region may lead to deviations in the
measurement results.

Measuring range (MR)

n

Region in which the measurement object must be present for the sensor to deliver reliable
measurement results.

n

Unwanted objects (objects not to be measured) in this region may lead to deviations in the
measurement results.

n

The limits of the measurement range (MR) are defined via the parameters 

Start of the mea-

surement range (Sdc)

 and 

End of the measurement range (Sde)

.

Zero position (ZP)

n

In the factory settings, the zero point is located on the front of the sensor (ZP = 

0 mm

). The

output consists of the distance between the front of the sensor and the object to be mea-
sured.

n

The following values depend on the zero position:
▪ Output measured values
▪ Switching points

n

Capable of parameterization via:
▪ Modbus RTU
▪ Teach button

Содержание 11233538























































Отзывы:

Нет отзывов