12
13
BEFORE USING YOUR COOKER HOB
RECOMMENDED ENVIRONMENTAL SAFEGUARDS
Before you use this cooker hob we suggest that you read the
instructions carefully and keep them for future consultation.
• Keep packing material (plastic bags, styrofoam blocks, etc...) out of
the reach of children as they can be dangerous.
• Make sure the cooker hob is intact and has not undergone damage
during shipment.
• Make sure the installation and gas and/or electric connections are
made by a qualified expert according to the manufacturer’s
instructions and in compliance with the local regulations in effect.
• Any exhaust hoods installed over the cooker hob should be
positioned at the height indicated (pict. A).
Packing: the packing material can be recycled and is marked with the
recycle symbol. Pieces of styrofoam, if any, should not be disposed of
carelessly. Dispose of this waste material at local dumps.
Product: the cooker hob is made of materials suitable for recycling.
Dispose of it in respect of the local regulations for waste disposal, after
making sure it cannot cause any damage. We recommend cutting the
power cable.
FOR INSTALLERS
TECHNICAL INFORMATION
Installation of BUILT-IN UNIT
To install built-in cooker hobs make an opening in the top of the cabi-
net with measurements A-B (pict. 1) as indicated in mm. in the table
below:
For the flush-mount version of the hobs (model 7043, 7044, 7045)
please refer to the specific instructions inside the box.
Note: Before installing make sure the local gas distribution system (type
and pressure of the gas) and settings of the cooker hob are compatible
(see rating plate).
Before installing the unit, remove any protective film.
Any laminate on the walls of the cabinet or adjacent appliances must
be heat resistant (heating protection "Y" according to standards EN
60335-2-6).
FASTENING OF UNIT
Apply the sealing gasket along the edge of the opening taking care to
overlap the joints (fig. 2). Place the cooker hob in the opening on the
cabinet. With a tool, slide plate A and fasten it with screw B (fig. 3). To
install cooker hobs size 76x50, mod. SOFT 79x50 and mod. FILO TOP,
see the installation instructions shown in pict. 3/A.
Fit hook B in angle iron A welded on the unit (fig. 3/A) taking care to
block it in the holes provided, depending on the thickness of the TOP.
Turn tab C and position it under the TOP, then tighten screw D. Trim
the part of the gasket extending beyond the cooker hob. For models
with sliding fastening hooks, see the instructions in the package.
For models 7045, 7041, 7042, see pict. 3/B.
IMPORTANT!!!
The counter top under the hob must be at least 3 mm below the
bottom and should have an opening for passage of the gas pipe and
electric wires measuring at least 50x50 mm. The adjacent surfaces
(bottom and back) of any cabinets over the counter top must be at least
50 mm above it. In case of elements sold complete with cabinet, the
instructions for installation of the cooker hob are provided in the
manual for the cabinet.
Installation must be made by a kitchen installation expert.
CONNECTION TO GAS MAINS
Must comply with the local regulations in effect. Connection must be
made with flexible steel tubing against the wall or with a rigid copper or
steel pipe (pict. 4-5).
IMPORTANT!!!
If flexible stainless steel tubing is used, it must be installed in such a
way that it does not come into contact with any moving parts, but
should pass in a point free of encumbrances so that it can be inspec-
ted along its entire length. After connecting the unit to the gas mains
always check the seal of the connection using a solution of soapy water.
Never check the seal using a flame.
The gas connector is a 1/2” gas threading ISO R7 conical connector.
If the cooker hob is installed in a cabinet with doors, it is important for
the rear wall of the cabinet to provide good airing. In case of a column
unit, adjacent to the cooker hob, it should be at least 100 mm away
from the outer edge.
The gas supply system must comply with the local standards in effect (see
chapter “National Reference Standards”).
CONNECTION TO POWER MAINS
• Connection to the power mains must be made by a qualified person
according to the regulations in effect.
• The installer is responsible for proper connection complying with the-
safety regulations.
• The cable supplied with a unit (if supplied without the plug) should
be provided with a plug suitable for the load indicated on the rating
plate, which should be plugged into a suitable grounded outlet.
• Connection can be made directly to the mains after inserting an omni
polar circuit breaker with minimum opening of 3 mm between the
unit and the mains, suitable for the load and complying with the
regulations in effect.
• The ground cable must not be cut off by the switch.
• The power cable must not touch parts that exceed room temperature
(pict. A)
B
A
R
29x50 cooker hobs
480
270
59x50 cooker hobs
480
570
76x50 Mod. 7024V
480
740
86x50 cooker hobs
480
840
76x50 Mod. 7065V
480
570/740
79x50 cooker hobs
480
770
116x50 cooker hobs
480
1140
Rondò Ø 52 units
diam. 500
/
79x50 cooker hobs Soft
480
770
135
92x54 cooker hobs
520
900
Cooker hobs angolare
(fig. 1A)
Dimensions of burner
unit and counter
(pict.
3)
(pict. 3/b)
(pict. 3/a)
(pict. 4)
(pict. 5)
(fig. 1)
(fig. 2
)
480
33
0
8
1
0
480
330
810
610
6
1
0
20x45∞
200x
45∞
(fig. 1A)
B
A
R
