background image

16

Safety cut-off 

o

If one or more of the cooking zones are accidentally left on, a 
safety cut off will activate after a certain period of time. The 
length of time depends on the power level that a zone or zones 
have been set on. 

LEVEL TIME LIMIT (hours)

1

8

2

8

3

8

4

4

5

4

6

4

7

2

8

2

9

2

o

If more than one zone is operating when one of the zones 
reaches its safety cut-off point, only the zone which has reached 
its safety cut off point will switch off. 

Hob guidelines 

o

The first few times the hob top is used, it may give off an acrid, 
burning smell. This smell will disappear completely with repeated 
use.

o

The worktop is fitted with cooking areas of different diameter 
and power. 

o

The positions where the heat will radiate from are clearly marked 
on the hob top. The saucepans must be positioned exactly on 
these zones for efficient heating to occur. Pans should have the 
same diameter as the cooking zone that they are being used on. 

o

You should not use saucepans with rough bottoms, as this can 
scratch the ceramic surface. 

o

Before use, make sure that the bottoms of the saucepans are 
clean and dry. 

o

When cold, the bottom of the pans should be slightly concave, as 
they expand when hot and lie flat on the surface of the hob. This 
will allow the heat to transfer more easily. 

Содержание BHC606BE





























Отзывы: