manualshive.com logo in svg

Baumalight TRL620Y, Руководство оператора

Поделиться
Скачать
Baumalight TRL620Y Скачать руководство пользователя страница 31

5 SERVICE AND 

MAINTENANCE

5.1 Safety

^

 

WARNING

Prevent death or serious injury.

1. 

Park machine on firm, level surface.

2. 

Engage park brake.

3. 

Verify all controls are in neutral.

4. 

Stop engine and remove key.

 

^

 

WARNING

Prevent death or serious injury.

Raised unsupported lift arms can fall, 

resulting in death or serious injury.

Never enter the area under raised lift 

arms.

Refer to the engine OEM manual for detailed 

operation, service interval and maintenance 
information.

5.2 Daily Or Every 10 Hours

Check Engine Oil Level

1. 

Skidsteer must be parked on a level surface, 

park brake engaged, lift arms fully lowered, 

engine stopped and key removed. 

2. 

Loosen knobs (A) and pivot hydraulic oil cooler 

upward. Engage pin to hold cooler in open 

position.

3. 

Remove second engine side panel from the 

front on left side of skidsteer.

A

A

4. 

Clean around oil dipstick (B). 

A

5. 

Check oil level on dipstick (B). Oil level should 

be at full mark on dipstick. Add OEM specified 

engine oil as necessary through fill port (C) on 

valve cover.  

C

27

Содержание TRL620Y

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды