Baumalight DSA530 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 28

Baumalight DSA530 Скачать руководство пользователя страница 20

4�11 Pressure Relief Adjustment

^

WARNING

Prevent serious injury or death caused

by unexpected movement:

1�

Park on a level surface�

2�

Lower tree saw the to ground�

3�

Engage parking brake�

4�

Shut off engine and remove key.

1. Park on a level surface.
2. Lower tree saw to the ground.
3.

Engage parking brake, shut off engine and

remove key.

(A) Flow Adjust - Adjusting the flow determines

how much oil is sent to cylinders and blade.

The more oil that is sent to the blade will result

in cylinders moving slower. If more oil is sent to

the cylinders, blade speed will decrease. Typical

adjustment is 1/2 turn out from closed position. To

adjust, hold hex screw with hex wrench and loosen

lock nut. Turn hex screw and hold in position while

tightening lock nut. Test operation and adjust again

if desired.
(B) Pressure relief must be set lower than

machine relief. 1/4 turn out from closed position

is approximately 3000 psi (207 bar). To adjust,

hold hex screw with hex wrench and loosen lock

nut. Turn hex screw in to increase pressure, or

out to decrease pressure. Turn hex screw in 1/4

turn increments until desired pressure is achieved.

Hold hex screw in position while tightening lock

nut.
Image is shown with top cover removed for

adjustments. Do not operate with top cover

removed.

A

B

18

«
...
18
19
20
21
22
...
»

Содержание DSA530





























Отзывы:

Нет отзывов