Bastl Instruments KOMPAS Скачать руководство пользователя страница 17

Страница: 17 / 17

FINAL ASSEMBLY

Congratulations! You have made it through. Now just put the boards back together, put the

faceplate

on (secured by the screw and nuts with washers) and your KOMPAS is ready to work! Oh and don’t

forget to put the

knobs

and

jumpers

on (the

led0

led1

led2

positions; 4th jumper must be left

unconnected for default operation - see picture).

Before you connect anything, make sure that your system is disconnected from power. Also double

check the polarity of the ribbon cable, the red cable should match the -12V rail both on the module

and on the bus board!

TROUBLESHOOTING

If you have any issues with the module, please check the

F.A.Q.

at our website first. You can reach us

here:

[email protected]

. We also provide service for the DIY stuff called Come to Daddy

(available at

https://noise.kitchen

Содержание KOMPAS


















Результаты поиска

Содержание KOMPAS

Отзывы:

Похожие инструкции для KOMPAS

Бренды по названию

Популярные бренды

Bastl Instruments KOMPAS, Инструкция по сборке

Результаты поиска

Содержание KOMPAS

Отзывы:

Похожие инструкции для KOMPAS

Бренды по названию

Популярные бренды