Basler BE1-CDS220 Скачать руководство пользователя страница 418 | Manualshive

Страница: 418 / 476

background image

14-28 BESTCOMS

Software BE1-CDS220

View Fault Details

To view the fault record details, select an event by clicking on the event number or anywhere on the event
line. The event grays-out while the information is being retrieved from the relay. View the fault details in
the associated window.

View Fault Sequence of Events

To view the fault record sequence of events, click on the radio button by the View Fault Sequence of
Events. View the fault sequence of events in the associated window.

Download Oscillography File

To download an oscillography file, select the type of file to download: Binary or ASCII. Click on the
Download button in the View/Download Relay Fault Files dialog box. Use normal Windows



techniques to

select the computer folder that is to receive the download file. You may create a new folder at this time by
clicking on the New Folder button. Okay the file save and the Fault Record Filenames dialog box opens.
Use the default Base Filename or enter a new file name. As you change the file name, the names for the
Header File, Fault Sequence, and Fault Summary also change automatically. OK the file names and then
exit the dialog box. You have now downloaded the oscillography file. You may view this oscillography file
using Basler Electric's BESTwave software.

METERING

To observe the system metering, pull down the Reports menu from the pull-down menu and select
Metering. When the Metering dialog box (Figure 14-39) opens, click on the Start Polling button. If
BESTCOMS is not configured to the relay communication settings, you will receive a Communications
Error. The Metering dialog box has two pull-down menus: File and Communication. To configure
communication with the relay, pull down the Communication menu and select Configure. Choose the
Com Port and Baud Rate, as required. If you have communication with the relay, click on the Start Polling
Button. Metering values are displayed. If you select Configure with polling in progress, you will get the
Polling Active dialog box. You must stop polling before you can change configuration. To stop polling,
click on the Stop Polling button. To exit, pull down the File menu and select Exit. You may also use the
Windows



techniques and click on the close icon (X) in the upper right-hand corner of the Metering dialog

box.

Figure 14-38. Metering from Reports Pull-Down Menu

«
...
416
417
418
419
420
...
»

Содержание BE1-CDS220





























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-CDS220

Бренд: Seg Страницы: 36

Бренд: Eaton Страницы: 2

Z-one ZSR101 Series

Бренд: CALEFFI Страницы: 52

Бренд: FRER Страницы: 28

Бренд: VERIS INDUSTRIES, INC. Страницы: 2

Бренд: Basler Страницы: 135

Бренд: C&S Страницы: 16

Бренд: Contrel Страницы: 4

Бренд: Omicron Страницы: 142

Бренд: Eaton Страницы: 16

AGM2-10-PKZ0-PI

Бренд: Eaton Страницы: 2

Бренд: IDEM SAFETY SWITCHES Страницы: 4

Бренд: GE Страницы: 16

Бренд: Reznor Страницы: 2

Бренд: Woodward Страницы: 70

Бренд: Vimar Страницы: 2

Бренд: Vimar Страницы: 2

SMART AUTOMATION BY-ME PLUS

Бренд: Vimar Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды