Bartell BM90 страница 13 Скачать руководство пользователя

Страница: 13 / 26

WALK BEHIND POWER TROWEL INSTRUCTION MANUAL

STORAGE

The following steps should be taken to prepare your

Walk-Behind Power Trowel for extended storage.

1. Close fuel shut off valve.

2. Siphon excess gasoline from tank.

3. Start engine until it stops from lack of fuel. This will

use up all the fuel in the carburetor and prevent

formation of deposits due to evaporation of fuel.

4. Remove spark plug and pour 2 oz. of SA

10W 30

motor oil into the cylinder. Slowly crank

the

engine

2 or 3 times to distribute the oil throughout

the cylinder. This will help prevent rust during

storage. Replace spark plug.

5. Store the unit in an upright position in a cool, dry,

well ventilated area.

MAINTENANCE

Maintaining your Walk-Behind Power Trowel will insure

long life to the machine and its components.

AIR CLEANER

- Keep air filter clean at all times. Wash

away dust and debris using a non-oil based cleaning

solvent. Let the filter dry before re-installing.

LUBRICATION

– Check engine oil regularly. Use

proper engine oil as recommended. See previous

chart. Fill crankcase to levels as recommended in

manufacture’s engine manual.

SPARK PLUG

–

Check and clean spark plugs

regularly. A fouled, dirty or carboned spark plug causes

hard starting and poor engine performance. Set spark

plug gap to recommended clearance. Refer to engine

manual.

BELT TENSION –

IMPORTANT!

If there is excessive belt play, there will be a decrease

in the power transmission capability which could lead to

premature wear and failure of the belt. The normal belt

play should be 1/2” to 5/8” which is attained by

depressing one side of the belt at the mid-point of the

span between pulleys. Tighten all engine mount

fasteners.

CHART FOR MINIMUM WIRE SIZE OF EXTENSION CORD

Nameplate AMPS

CORD LENGTH

25’

50’

100’

150’

0-6

18 AWG

16 AWG

14 AWG

6-10

18 AWG

16 AWG

14 AWG

12 AWG

10-12

16 AWG

14 AWG

12 AWG

12-16

14 AWG

12 AWG (NOT RECOMMENDED)

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA L5T 3A7, 905-364-4200 FAX 905-364-4201

CREATED: 07/04

REVISED: 05/10

CREATED: 06/12

Содержание BM90



























Результаты поиска

Содержание BM90

Отзывы:

Похожие инструкции для BM90

Бренды по названию

Популярные бренды

Bartell BM90, Руководство пользователя и каталог запасных частей

Результаты поиска

Содержание BM90

Отзывы:

Похожие инструкции для BM90

Бренды по названию

Популярные бренды