manualshive.com logo in svg

Bartec P-600, Руководство пользователя, Страница: 35 / 60

Поделиться
Скачать
Bartec P-600 Скачать руководство пользователя страница 35

 

 

P-600 SIC Analyzer Manual

 

Chapter IV: Programming 

 

29 

 

Alarm Critical 

–  

This type of alarm indicates Analysis has stopped because one of the 
critical conditions has been detected. 

Maintenance 

– 

Activated when the number of measurement cycles has exceeded the 
Max Cycles setting. 

Stream 1 

– 

stream 1 is being measured. 

Stream 2 

– 

stream 2 is being measured. 

Come Read 

– 

Activated for a programmed period of time upon the completion of a 
measurement cycle. 

In Validation 

– 

validation cycle is being performed. 

Valid. Pass 

– 

validation cycle passed. 

 

•

 

Conditions 

— 

This designates whether the alarm relay will energize or de-energize when an 

alarm condition is detected. When Normal is selected, power will be applied to the relay when an 
alarm condition is detected; when Failsafe is selected, power will be removed from the relay when 
an alarm condition is detected. 

 

Communications Setup 

The Communications submenu allows you to configure the Analyzer’s Serial and Modbus settings.

 

 

 

 
Serial Port C 

This is the Analyzer’s RS-232 serial communication port.

 

 

•

 

Mode 

— 

This menu item determines what data will be output through the RS-232 port. The 

choices are Result, Data, and None.

 

•

 

Rate 

— 

This is the baud rate used for serial communications through this port (9600 / 19200 / 

38400).

 

 
Modbus 

Содержание P-600





























































Отзывы:

Нет отзывов