Bartec P-600 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 60

Bartec P-600 Скачать руководство пользователя страница 32

P-600 SIC Analyzer Manual

Chapter IV: Programming

26

NOTE: If Salt in Crude graphing is enabled, the graph is updated at the
end of each measurement.

Alarm Settings

This submenu screen is used to program the Analyzer’s alarms.

Use the Index key to move to the desired menu item. Use the Up/Down Arrow keys to change the displayed
setting or value. The unit of measure used for these values is set in the Other Settings submenu.

Warning Alarms

Those types of alarms do not stop the analysis.

“Result out of range” warning alarm is activated when the

measured concentration exceeds the indicated value.

•

Low

—

This menu item allows you to establish a low alarm level. Salt concentration

measurements below this value generate a warning alarm signal/message. Analysis will continue.

•

High

—

This menu item allows you to establish a high alarm level. Salt concentration

measurements above this value generate a warning alarm signal/message. Analysis will
continue.

Critical Alarms

Those types of alarms stop the analysis. Programmable critical alarm is a maximum cell temperature.

•

Maximum Temperature

—

This menu item allows you to establish a maximum allowable cell

temperature. Cell temperatures above this value generate a critical (fatal) alarm signal/message
and stops analysis.

•

Rem Stdby

—

Enables or Disables Alarm Critical when in Remote Standby mode.

«
...
30
31
32
33
34
...
»

Содержание P-600





























































Отзывы:

Нет отзывов