Barry-Wehmiller Accraply 204RH Скачать руководство пользователя страница 36

Страница: 36 / 97

SECTION 1: SYSTEM OPERATION

1.5.3 Alarm Indicators

LIGHT STACK:

RED

YELLOW

GREEN

COLOUR

DESCRIPTION

SYSTEM REACTION

SOLID RED

Error/Fault

System is stopped. See operator control panel for fault

indicator.

SOLID

YELLOW

Head Warning (Low Label)

System will continue to run. Warning from labeling head

could be low label or other head warning. A warning code

will be displayed on the keypad. Head warnings are listed

in the 204 manual.

FLASHING

YELLOW

Challenge mode

The system is in challenge mode.

SOLID

GREEN

Conveyor Running

System has no errors and conveyor is running.

FLASHING

GREEN

The clearance sensor has detected

the next product before the wipe-down

sequence has completed.

System has no errors. Conveyor and spacing wheels

paused due to clearance pause alarm.

CONTROL PANEL INDICATORS:

LIGHT

FLASHING

SOLID

SENSOR/CYL

• Sensor Failure (wipe-down/evaluation or

eject verification/bin full)

• Bin Full

• Cylinder Position Fault

• Air Pressure out of range

INSPECTION

• 3 Consecutive Failures

• Eject Verification Failure

• Product Too Long (back to back)

HEAD/DRIVE

• VFD Fault

• 204 Not Ready

• Safety Circuit (E/Stop or Interlock)

For descriptions of these alarms, see 1.5.4 Alarm List

OPERATING PROCEDURES

Содержание Accraply 204RH


































































































Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды

Barry-Wehmiller Accraply 204RH, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды