Barry-Wehmiller Accraply 204RH Скачать руководство пользователя страница 22

Страница: 22 / 97

SECTION 1: SYSTEM OPERATION

1.3 General Information

1.3.1 Shipping and Handling

1. Position the Labeler where it is going to be used. Make sure it is properly balanced and secure.

2. Remove all banding and wrapping materials (including plastic tie wraps, cloth bands, padding, etc.) that were

installed for shipping.

Note: The Labeler may be heavier on one side due to installed equipment. Be careful when lifting the machine that it

does not tilt to one side and fall over.

1.3.2 Service Requirements

Capacity/Characteristics

Electrical

120 VAC

Air

80 PSI

See Section 3 for more detailed requirements.

1.3.3 Technical Data

Products

Carton: 7-3/4” L x 5-3/8” W x 1-1/4” H

Labels

Seal: 1-3/4” L x 3/4” W

Line Speeds

20 Products per minute

System Description

• Accraply 204 Label Applicator

• Ultrasonic Label Sensor for Clear or Opaque Labels

• Dual Label Application Set-Up

• Automatic Product Speed Following Encoder

• Product Sensor Assembly

• Mounting Assembly

• Belt Conveyor

• Dual Product Gating/Spacing Wheels

• Carton Rotation Device

• Custom Label Wipe-Down

• Cognex Checker System

• Carton Eject System

• Electrical Panel

• AB PLC

• Alarm Package

• Alarm Light Mounting Post

• Safety Guarding

• Lockable Air Shut-Off

• Air Dump with Soft Start

• Carton Squaring Device

GENERAL INFORMATION

Содержание Accraply 204RH


































































































Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды

Barry-Wehmiller Accraply 204RH, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Accraply 204RH

Отзывы:

Похожие инструкции для Accraply 204RH

Бренды по названию

Популярные бренды