background image

LD1 REAR BUMPER 

2007-16 CHEVY SILVERADO 1500 

 Page 1 of 6 

8/26/16 (DP) 

   
 

PARTS LIST: S101325  S101326

 

LD1 Rear Bumper Assembly 

12-1.75mm x 35mm Hex Bolts 

Driver/left Frame Bracket 

12mm x 37mm OD x 3mm Flat Washers 

Passenger/right Frame Bracket 

12mm Nylon Lock Nuts 

License Plate Light 

10-1.5mm x 50mm Hex Bolts 

License Plate Plugs 

10mm x 34mm OD x 3mm Flat Washers 

Sensor Hole Plugs 

10mm Nylon Lock Nuts 

Trailer Plug Bracket 07-13 

6mm x 16mm Hex Bolts  

Trailer Plug Bracket 2014+ 

6mm ID x 12mm OD x 1.6mm Flat Washers 

10  Nylon Wire Ties 

6mm Nylon Lock Nut 

14-2.0mm x 45mm Hex Bolts 

4mm Allen Wrench 

12  14mm x 28mm OD x 2.5mm Flat Washers 

4mm x 10mm Button Head Bolts 

14mm Nylon Lock Nuts 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
PROCEDURE: 

 

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS 
CAREFULLY BEFORE STARTING INSTALLATION. BUMPER IS HEAVY, ASSISTANCE IS HIGHLY 
RECOMMENDED TO AVOID POSSIBLE INJURY OR DAMAGE TO THE VEHICLE.   

1. 

Remove the license plate. On models with bumper sensors, unplug all sensors. Remove the trailer plug 
from the bumper. Release the wiring harness from the clips attached to the back of the bumper and 
move harness away from bumper as necessary. 

 

2. 

Place blocks or jack stands under the bumper to support it during mounting bolt removal. 

3. 

Determine procedure for your model year: 

07-13 Models. 

a. 

Starting on the passenger/right side, remove (2) hex bolts attaching bumper to top/center of 
receiver hitch if equipped. 

b. 

Remove hex bolts from side and bottom of frame, 

(Figures 1—3)

.  

c. 

Repeat previous Steps to remove driver/left side hardware. 

d. 

With assistance, pull bumper and brackets straight out from vehicle, 

(Figures 6 & 7)

14-16 Models.

 

a. 

Starting on the passenger/right side, remove rear bolts attaching bed to frame, 

(Figure 2)

Loosen center bolts (if equipped). Do not loosen front bolts. 

b. 

Remove hex bolts from side and bottom of frame, 

(Figures 1—3)

c. 

Repeat previous Steps to remove driver/left side hardware. 

License Plate Light 

(4) Sensor 
Hole Plugs 

(2) Plastic Nuts for License Plate 

Passenger/right 
Frame Bracket 

Driver/left 
Frame Bracket 

2014-on Trailer 
Plug Bracket 

2007-13 Trailer 
Plug Bracket 

Содержание LD1







Отзывы: