background image

3107C OWNER’S MANUAL                           2/01/23                                  Page 3 of 18 

SAFETY MESSAGES 

 

This section covers the method used to announce safety messages. Safety messages appear as appropriate 
in this manual and on decals affixed to the machine where a hazard may occur if procedure or instructions 
are not followed correctly and completely. 
 

This is the ISO general warning sign it has been adapted for black and white printing. 
Standard No.: 7010:2011   

 
It is used in conjunction with the following signal words to communicate a hazard.  
 
From: ISO 3861-2.2004 

 

DANGER

: Indicates an imminently hazardous situation which, if not avoided, will result in 

death or serious injury. 

 

WARNING

: Indicates a potentially hazardous situation which, if not avoided, could result in 

death or serious injury.   

 

CAUTION

: Indicates a potentially hazardous situation which, if not avoided, could result in 

minor or moderate injury.  

Study ALL decals on the 3107C before operating the 3107C. 
 

ALWAYS USE COMMON SENSE AND THINK SAFETY FIRST! 
 

Review the 

SAFETY INSTRUCTIONS OVERVIEW 

found in the operator’s manual  

 

 

Emergency & Medical Contacts: 
USA & CANADA

: Emergency dial 

911

 

USA & CANADA

: American Association of Poison Control Centers: 

1-800-222-1222 

 
Outside the USA & Canada (Please fill in the appropriate number) 
 
National Emergency number:_______________ 
 
Poison Control Center:____________________ 
 
Other:_________________________________ 

Содержание 3107C



















Отзывы: