background image

8

To avoid the possibility of the appliance plug or receptacle getting wet, position the saw to one side of a wall 

mounted receptacle.  This will prevent water from dripping onto the receptacle or plug.  A “drip loop,” shown 

should be arranged by the user to properly position the power cord relative to the power source.

The “drip loop” is that part of the cord below the level of the receptacle, or the connector, if an extension cord 

is used.  This method of positioning the cord prevents the travel of water along the power cord and coming in 

contact with the receptacle.

If the plug or receptacle gets wet, DO NOT unplug the cord.  Disconnect 

the fuse or circuit breaker that supplies power to the tool.  Then unplug and 

examine for presence of water in the receptacle.

Use only extensions cords that are intended for outdoor use.  These extension 

cords are identified by a marking “Acceptable for use with outdoor appliances; 

store indoors while not in use.”  Use only extension cords having an electrical 

rating not less than the rating of the product.  Do not use damaged extension 

cords.  Examine extension cords before using and replace if damaged.  Do not 

abuse extension cords and do not yank on any cord to disconnect.  Keep cords 

away from heat and sharp edges.  Always disconnect the extension cord from 

the receptacle before disconnection the product form the extension cord.

To reduce the risk of electrocution, keep all connections dry and off the ground.  Do not touch the plug with wet 

hands.

Use of under size extension cords result in low voltage to the motor that can result in motor burnout and 

premature failure.  Barranca Diamond warns that equipment returned to us showing signs of being run in a 

low voltage condition, through the use of undersized extension cords will be repaired or replaced totally at the 

customers expense.  There will be no warranty claim.

Drip Loop

 

 

 

 

BD-10 

           SAFETY

To choose the proper extension cord,

•  Locate the length of extension cord needed in Table below.

•  Once the proper length is found, move down the column to obtain the correct AWG size 

required for that length of extension cord.

EXTENSION CORD LENGTH

Nameplate 

Amperes

115V

25'

50'

75'

100'

150'

200'

250V

50'

100'

150'

200'

300'

400'

0 - 5

16

16

16

14

12

12

5.1 - 8

16

16

14

12

10

8.1 - 12

14

14

12

10

12.1 - 15

12

12

10

10

15.1 - 20

10

10

10

Содержание BD10





































Отзывы: