Baroness LM551B Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 172

background image

If the oil cooler has been contaminated with
dust, be sure to clean it.
Especially after operating the machine in a
dusty environment, it is important to remove
dust as soon as possible.

Open the radiator cover.
Unlock the rubber catches on the left and
right of the oil cooler, and then tilt the oil
cooler.

1

1

2

3

va4j43-017

Cleaning of Oil Cooler_001

1

Rubber catch

2

Oil cooler

3

Radiator

Carefully clean the front and back of the oil
cooler with water or compressed air.

Hydraulic Oil

Inspection of Hydraulic Oil

The oil gauge is on the side of the hydraulic
tank.

Raise the mower units and maintain that
position on a level surface.
Make sure that the oil level is at the middle
of the oil gauge.

1

olekci-005

Inspection of Hydraulic Oil_001

1

Oil gauge

Check underneath the machine for oil
leakage.

1.
2.

3.

1.

2.

3.

Supply of Hydraulic Oil

Important

Do not mix different types of oil.

Important

Use Shell Tellus S2M46 (or equivalent) as
hydraulic oil.
In case of an equivalent, consult
Characteristics of Hydraulic Oil and use
hydraulic oil whose characteristics are
superior to those of the specific hydraulic oil.
Especially regarding kinematic viscosity and
viscosity index, use of hydraulic oil whose
figures are less than those of the specified
hydraulic oil will cause a malfunction in the
hydraulic circuit.

Note:
Characteristics of Hydraulic Oil

Specified Hydraulic Oil

Shell Tellus S2M46

ISO Viscosity Grade

ISO VG46

Density

15 °C (59 °F)

0.873 g/cm

3

(0.0315 lb/in

3

)

API Gravity

30.6

Flash Point (Open Cup)

230 °C (446 °F)

Pour Point

-30 °C (-22 °F)

Kinematic
Viscosity

40 °C (104 °F)

46 mm

2

/s (46 cSt)

100 °C (212 °F)

7 mm

2

/s (7 cSt)

Viscosity Index

109

Remove the screws from the tank cover,
and then remove the tank cover.

2

2

1

dmhzyz-018

Supply of Hydraulic Oil_001

1

Tank cover

2

Screw

1.

Handling Instructions

LM551B

Handling Instructions

Page 4-7

Daily Check List

«
...
35
36
37
38
39
...
»

Содержание LM551B













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LM551B

Бренд: Cadet Страницы: 40

Бренд: Snapper Страницы: 40

Бренд: MTD Страницы: 20

Бренд: Gtech Страницы: 28

Бренд: Scag Power Equipment Страницы: 41

Hako-Profi-Flipper

Бренд: HAKO Страницы: 27

Бренд: Kubota Страницы: 16

Бренд: Cub Cadet Страницы: 44

Бренд: Sealey Страницы: 4

Бренд: Cadet Страницы: 39

Бренд: Snapper Страницы: 176

Бренд: Briggs & Stratton Страницы: 128

Бренд: Toro Страницы: 8

Бренд: Toro Страницы: 8

Бренд: Texas Equipment Страницы: 20

Бренд: Toro Страницы: 16

Бренд: Gardena Страницы: 15

Super Recycler 20792

Бренд: Toro Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды