Baroness LM551B Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 172

background image

Adjustment of Parking Brake

Caution

Make sure that the brake wire is not cracked
or damaged.

Important

Make sure that the brake is effective on
slopes and that it is not applied any longer
when you release it.
Adjust the parking brake whenever there is
any abnormality.

Stop the engine.
Remove the step cover.
Follow the steps below to adjust the parking
brake.

Depress the locking pedal while firmly
depressing the brake pedal to lock it and
engage the latch in a notch.

3

2

1

A

ulabms-016

Adjustment of Parking Brake_001

1

Brake pedal

2

Latch

3

Notch

A

Fourth or fifth notch

1.
2.
3.

[1]

Adjust the adjustment bolt so that the latch
is positioned in the fourth or fifth notch
from the top.

2

1

1

2

3

3

ulabms-013

Adjustment of Parking Brake_002

1

Brake wire

2

Adjustment bolt

3

Lock nut

Adjustment of Brake

Caution

If the brake wire is cut, the machine will be
unable to stop.
If the brake wire is cracked or damaged,
immediately replace it with a new one.
If the brake is not sufficiently effective, adjust
the brake wire.

Important

Make sure that the brake is effective on
slopes and that it is not applied any longer
when you release it.
Adjust the parking brake system whenever
there is any abnormality.

Stop the engine.
Remove the step cover.

1

nfzln9-027

Adjustment of Brake_001

1

Step cover

[2]

1.
2.

Maintenance

LM551B

Maintenance

Page 5-33

Maintenance Work

«
...
145
146
147
148
149
...
»

Содержание LM551B













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LM551B

Бренд: Lastec Страницы: 69

Бренд: SANLI Страницы: 16

Бренд: Parker Страницы: 26

Бренд: Cub Cadet Страницы: 68

Бренд: Alamo Страницы: 168

Craftsman 917.250262

Бренд: Sears Страницы: 60

Бренд: Yard Pro Страницы: 108

Бренд: Land Pride Страницы: 58

Бренд: Gtech Страницы: 68

PARK 13-6113-56

Бренд: Stiga Страницы: 2

Бренд: Yard force Страницы: 49

Бренд: Snapper Страницы: 12

Бренд: Worx Страницы: 24

Broardmoor 2600, 1600, LT Series

Бренд: Simplicity Страницы: 2

Бренд: Kubota Страницы: 24

Бренд: Cub Cadet Страницы: 40

Бренд: Husqvarna Страницы: 29

Бренд: Husqvarna Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды