Baroness LM551B Скачать руководство пользователя страница 145

Страница: 145 / 172

Mower unit position: Rear
Use the center locking hole (B) for
maintenance.

sibu71-013

Swiveling Mower Units #2 and #3_005

Grip pin

Pipe pin

Start the engine, and then raise the mower
units.

sibu71-014

Swiveling Mower Units #2 and #3_006

Mower unit

After the maintenance is completed, reverse
the procedure to return the machine to its
original condition.

Removing/Installing Tires

Front Tires

Follow the steps below to remove the front
tires:

Loosen the bolts.

lm2ieh-002

Front Tires_001

Heat-treated bolt

Securely place the jack beneath the jack-up
point of the front left/right frame area, and
then raise it until the tire lifts off the ground.
"Jack-Up Points" (Page 5-22)
Remove the bolts.
Remove the tire from the wheel mounting
seat.

Important

Tighten the bolts in the tightening order
(diagonally).

For installing the front tires, reverse the
removing procedure.

Rear Tire

Follow the steps below to remove the rear
tire.

Loosen the bolts.

upekw4-002

Rear Tire_001

3.
4.

Maintenance

LM551B

Maintenance

Page 5-31

Maintenance Work

Содержание LM551B













































































































































































Результаты поиска

Содержание LM551B

Отзывы:

Похожие инструкции для LM551B

Бренды по названию

Популярные бренды

Baroness LM551B, Руководство по эксплуатации для владельца

Результаты поиска

Содержание LM551B

Отзывы:

Похожие инструкции для LM551B

Бренды по названию

Популярные бренды