Baroness LM315GC Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 86

Baroness LM315GC Скачать руководство пользователя страница 30

Tire

Inspection of Tires

Check the pneumatic pressure of the tires.
Make sure that there are no cracks,
damage or abnormal wear.

(For green/For field)

　

Tire size

Pneumatic

pressure

Front wheel

Smooth 18 ×
9.50-8 2P

80 kPa
(0.8 kgf/cm

2

)

Rear wheel

Smooth 18 ×
9.50-8 2P

80 kPa
(0.8 kgf/cm

2

)

(For teeing ground)

　

Tire size

Pneumatic

pressure

Front wheel

Pillow Dia 18 ×
8.50-8 4P

100 kPa
(1.0 kgf/cm

2

)

Rear wheel

Pillow Dia 18 ×
8.50-8 4P

100 kPa
(1.0 kgf/cm

2

)

Brake

Inspection of Parking Brake

Make sure that the brake is applied when
you pull the parking brake lever.
Make sure that the brake is not applied
even slightly when you press the push
button to release the parking brake lever.

Belt

Inspection of Belt

Caution

If you have removed the cover during
inspection, make sure that you replace it in
the original position securely.
If the cover remains removed, the operator
may come in contact with the rotating objects
or belt, possibly resulting in injuries.

Important

A slacking or damaged belt may cause the
cutter rotation speed or operation speed to be
insufficient for operation.

Press the middle of the belt with your finger
to check the belt tension.

1.
2.

1.

2.

1.

Make sure that there are no cracks,
damage or abnormal wear.

Wire

Inspection of Wire

Make sure that the wire is not cracked or
damaged.
If the wire is cracked or damaged, replace it
with a new one immediately.

Engine

Inspection of Engine-Associated Parts

For details on handling the engine, please
refer to the Engine's Owner's Manual.

Check the fuel system parts for loosened or
cracked joints and leakage. Replace the
parts if necessary.
Blow compressed air to clean any grass or
flammable materials that may be attached
inside or around the muffler.

Engine Oil

Inspection of Engine Oil

For details on handling the engine, please
refer to the separate Engine Handling Manual.

Important

Securely tighten the oil level gauge and oil
filling port cap.

Stop the engine, wait for 10 to 20 minutes
for the engine to cool down, and then check
the oil level.
Position the machine so that the engine will
be level, then insert the oil level gauge all
the way to check the oil level.

1

2

bgmiun-011

Inspection of Engine Oil_001

2.

1.

2.

1.

2.

1.

2.

LM315GC

Handling Instructions

Page 4-6

Inspection Before Use

«
...
28
29
30
31
32
...
»

Содержание LM315GC























































































Отзывы:

Нет отзывов