Baroness LM285 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 65

Baroness LM285 Скачать руководство пользователя страница 60

If the belt becomes slack due to frequent use, it
may jump or slip.
In addition, if it is overtightened, it may wear
prematurely.
If necessary, adjust it, and always check the belt
for appropriate tension.

Fan Belt

Caution

Be sure to stop the engine before adjusting
the belts.

For details on handling the engine, please refer
to the separate Engine Operating Manual.

Press the middle of the belt with your finger
to check the belt tension.
If the belt is too slack, loosen bolts A and B
(that affix the alternator), then move the
alternator to adjust the tension.

2

5

3

4

1

10 mm(0.39 in)

sdie3r-002

Fan Belt_001

1

Fan belt

2

Blade

3

Alternator

4

Bolt A

5

Bolt B

Adjustment of Parking Brake

Danger

Danger

If the brake wire is cut, the machine will be
unable to stop. This would be extremely
dangerous.
If the brake wire is cracked or damaged,
replace it with a new one immediately.
If the parking brake is not sufficiently effective
when you pull the parking brake lever, adjust
the brake wire.

1.

2.

Adjust the parking brake by tightening the brake
wire adjustment bolt.

1

2

4

3

ulabms-003

Adjustment of Parking Brake_001

1

Parking brake lever

2

Lock nut

3

Adjustment bolt

4

Brake wire

Adjustment of Brake

Danger

Danger

If the brake wire is cut, the machine will be
unable to stop. This would be extremely
dangerous.
If the brake wire is cracked or damaged,
replace it with a new one immediately.
If the brake is not sufficiently effective, adjust
the brake wire.

Adjust the foot brake by tightening the foot brake
wire adjustment bolt.

3

4

2

1

nfzln9-002

Adjustment of Brake_001

1

Lock nut

2

Adjustment bolt

3

Brake wire

4

Brake lever

Break-in of Brakes

If the brake shoes or brake pads are worn,
replace them with new ones.

LM285

Maintenance

Page 5-12

Maintenance (Main Body)

«
...
58
59
60
61
62
...
»

Содержание LM285


































































Отзывы:

Нет отзывов