Baroness LM285 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 65

Baroness LM285 Скачать руководство пользователя страница 52

Specified Values

Fuel tank capacity

38.0 dm

3

(38.0 L)

Hydraulic tank capacity

24.0 dm

3

(24.0 L)

Shell Tellus S2M46 (or equivalent)

Quantity of engine oil

3.1 dm

3

(3.1 L)

Summer: SAE30, Winter: SAE20

Coolant volume

6.0 dm

3

(6.0 L)

Including 1.0 dm

3

(1.0 L) reserve tank

Type R

Front tire

120 kPa (1.2 kgf/

㎝

2

)

23 x 10.50 - 12 4P

Rear tire

150 kPa (1.5 kgf/cm

2

)

23 x 8.50 - 12 4P

Cutter adjustment spring

1 mm

Clearance of spring

Main Consumable Parts

Part Name

Code

Fan belt

PF1G345-9701-0

Oil element

PF16271-3209-2

Air cleaner element

PFT0270-1632-0

Fuel filter element

PF15231-4356-0

Suction filter element

K3413000020

Hydraulic cartridge filter

K3412000060

Hydraulic oil (20 L can)

K2913100200

Brake wire, left

K1120107000

Brake wire, right

K1120125000

Side brake wire

K1120141010

Throttle wire

K1110101000

Brake shoe, front right

P741-8005-00

Brake shoe, rear right

P741-8007-00

Brake shoe, front left

P741-8006-00

Brake shoe, rear left

P741-8008-00

Jacking up the machine

About the Jacking up the machine

Warning

When replacing a tire or beginning any other
maintenance or repairs, be sure to chock the
wheels to prevent the machine from moving.
Before jacking up the machine, park it on a
hard, flat surface such as a concrete floor and
remove any obstacles that could prevent you
from performing the work safely. When
necessary, use an appropriate chain block,
hoist, or jack. Support the machine securely
with jack stands or appropriate blocks. Failure
to do so may cause the machine to move or
fall, resulting in injury or death.

Use the jack-up points identified in this manual
when jacking up the machine.
Only place a jack under the jack-up points
specified. Placing a jack at any other point could
result in damage to the frame or other parts.

LM285

Maintenance

Page 5-4

Jacking up the machine

«
...
50
51
52
53
54
...
»

Содержание LM285


































































Отзывы:

Нет отзывов