Baroness LM285 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 65

Baroness LM285 Скачать руководство пользователя страница 18

Specification Decal

The Specification decal indicates the CE logo,
model name, and weight, etc.

kj8jic-001

Decal, Specifications_001

Noise Emission Decal

The noise emission decal indicates the sound
power level determined by measuring identical
machines in accordance with the procedure
specified in the EC directives.

jiwe3f-001

Noise Emission Decal_001

Year of Manufacture Decal

The year of manufacture decal indicates the
year when this machine was manufactured.

YEAR OF

MANUFACTURE

wvzv36-001

Year of Manufacture Decal_001

Safety and Instruction Signs

About the Safety and Instruction Signs

Warning

Safety labels and operation labels are
attached to this machine.
Make sure that they are preserved in their
entirety.
If they are damaged, become dirty, or peel
off, replace them with new ones.

Part numbers for labels that need to be replaced
are listed in the parts catalog.
Order them from a Baroness dealer or
Kyoeisha.

Positions of the Decals (Warning and

Instruction)

2,3

2,3

5

2,3

4

8

6

7

1

6iul4h-008

Positions of the Decals (Warning and Instruction)_001

LM285

Product Overview

Page 3-4

Safety and Instruction Signs

«
...
16
17
18
19
20
...
»

Содержание LM285


































































Отзывы:

Нет отзывов