manualshive.com logo in svg

Baroness LM2700, Руководство по обслуживанию

Поделиться
Скачать
Baroness LM2700 Скачать руководство пользователя страница 225

Installation of Steering

Caution

See "Tightening torques" (Page 3-5) .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

For installing it, reverse the removing
procedure.

Removal of Steering Column

Remove the steering wheel. (See "Removal
of Steering" (Page 7-30) .)
Remove the front cover. (See "Removal of
Front Cover" (Page 7-34) .)
Remove the hood. (See "Removal of Hood"
(Page 7-35) .)
Disconnect the differential lock wire.

1

2m1b1h-003

Removal of Steering Column_001

1

Differential lock wire

1.

2.

3.

4.

Remove the eight bolts and spring washers,
and then remove the steering column.
Note:
The front cover mounting bracket is
removed at the same time.

1

2

3

1

2

3

4

2m1b1h-004

Removal of Steering Column_002

1

Front cover mounting bracket

2

Spring washer

3

Bolt

4

Steering column

Installation of Steering Column

Caution

See "Tightening torques" (Page 3-5) .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

For installation, reverse the removing
procedure.

5.

Main

 bo

dy

LM2700

Main body

Page 7-31

Removal and installation of each section

Содержание LM2700






































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды