manualshive.com logo in svg

Baroness LM2700, Руководство по обслуживанию

Поделиться
Скачать
Baroness LM2700 Скачать руководство пользователя страница 167

Seat Switch

The seat switch is located right underneath the
seat and is not usually conducted.
It is normal if it is conducted when seated
(pressed).

6m8tje-003

Seat Switch_001

Parking Brake Switch

The parking brake switch is located at the brake
pedal fulcrum (under floor).

It is normal if the two wires of the parking
brake switch are conducted between them
when the brake pedal is depressed.
(Condition that switch operation part is
completely extended)
It is normal if the two wires of the parking
brake switch are not conducted between
them when the brake pedal is released.
[Condition that switch operation part is
completely retracted]

1

2

3

67xzzh-007

Parking Brake Switch_001

1.

2.

1

Switch operation part

2

Parking brake switch

3

Wire

Rocker Switch

The rocker switchs are located in the operation
panel and are used for the traveling/working
changeover switch, 2WD/4WD changeover
switch, reel rotation switch, and reel forward/
reverse switch.
Normal operation is when there is continuity
between sockets A and C with the rocker switch
in the "ON" position and no continuity between
sockets A and C with it in the "OFF" position.

1

C

A

t3inzb-002

Rocker Switch_001

1

Rocker switch

Elec

trical sy

stem

LM2700

Electrical system

Page 6-19

Electrical components

Содержание LM2700






































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды