Baroness LM101 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 88

Baroness LM101 Скачать руководство пользователя страница 39

1

4

5

3

2

2qrq2r-010

Adjustment of Groomer_006

1

Front groomer

2

High nut

3

Nut A

4

Bolt

5

Groomer adjustment screw

Note:
When not using the front groomer, there is
no need to change the set height of the
groomer.
The front groomer can be raised to a height
where it does not make contact with the
grass, by loosening the left side nut B and
right side bolt securing the groomer
adjustment screw, lifting up the front
groomer and tightening the left side nut B
and right side bolt.
To use the groomer again, the previous
height set for the groomer can be restored
by loosening the left side nut B and right side
bolt, lowering the groomer and tightening the
left side nut B and right side bolt.

Procedure to Start/Stop Engine

Start/Stop of Engine

Procedure to Start Engine

Caution

Before starting the engine, make sure that
there are no other people or obstacles around
the machine.

Caution

Make sure that the engine clutch cover is
installed in the prescribed position.

Make sure that the engine switch is in the
"OFF" position.

B

A

1

v2e27i-035

Procedure to Start Engine_001

1

Engine switch

A

ON

B

OFF

Make sure that the brake is locked.

2

1

A

B

ud9f2u-004

Procedure to Start Engine_002

1

Brake lever

2

Lock lever

A

Lock

B

Unlock

1.

2.

Handling Instructions

LM101

Handling Instructions

Page 4-17

Procedure to Start/Stop Engine

«
...
37
38
39
40
41
...
»

Содержание LM101

























































































Отзывы:

Нет отзывов