manualshive.com logo in svg

Baroness GM2810A, Руководство по эксплуатации для владельца, Страница: 88 / 155

Поделиться
Скачать
Baroness GM2810A Скачать руководство пользователя страница 88

Electrical Wiring

Inspection of Electrical Wiring

Important

Electrical short circuit will cause fire, electrical
leakage and malfunction of electrical
equipments.

Inspect electrical wiring for poor terminal
connections, damaged wiring or terminals,
loose connections, weather-related
deterioration and chemical-related
deterioration.
If necessary, repair before operating the
machine.

Tire

Inspection of Tires

Check the pneumatic pressure of the tires.
Make sure that there are no cracks,
damage or abnormal wear.

Tire size

Pneumatic pressure

Front wheel (29 x
14.00 - 15)

150 kPa (1.5
kgf/cm

2

)

22 psi

Rear wheel (20 x
12.00 - 10)

140 kPa (1.4
kgf/cm

2

)

20 psi

Brake

Inspection of Brake Pedal

When depressing the brake pedal fully,
make sure that there is appropriate
clearance between the floorboard and the
pedal or pedal reserve distance.
When depressing the brake pedal fully,
make sure that the pedal reaction is not
spongy and that there is no noise.
When depressing the brake pedal during
traveling, make sure that the machine stops
smoothly and the braking is sufficiently
effective.

Inspection of Parking Brake

Make sure that the parking brake is applied
after depressing the brake pedal and
pulling the parking brake lever.
Make sure that the parking brake is not
applied even slightly after depressing the
brake pedal to release the parking brake
lever.

1.
2.

1.

2.

3.

1.

2.

Belt

Inspection of Belt

Warning

The engine must be stopped when the belt is
inspected.

Important

A slacking or damaged belt or damaged fan
may cause overheating or lack of a battery
charge.

Press the middle of the belt with your finger
to check the belt tension.
Make sure that there are no cracks,
damage or abnormal wear.

Wire

Inspection of Wire

Make sure that the wire is not cracked or
damaged.
If the wire is cracked or damaged, replace it
with a new one immediately.

Safety Device

Inspection of Safety Device

Make sure that the safety device operates
correctly.
"Safety Mechanisms" (Page 4-9)

1.

2.

1.

2.

GM2810A

Handling Instructions

Page 5-10

Inspection and Cleaning

Содержание GM2810A




























































































































































Отзывы:

Нет отзывов