manualshive.com logo in svg

Baroness GM2810A, Руководство по эксплуатации для владельца, Страница: 83 / 155

Поделиться
Скачать
Baroness GM2810A Скачать руководство пользователя страница 83

Coolant

Inspection of Coolant

Caution

Do not touch the radiator or coolant during
engine operation or immediately after the
engine has been turned off.
Otherwise, you may get burned.

Caution

Inspection should take place after the engine
has well cooled down.

Make sure that the coolant level in the
reserve tank is between "FULL" and
"LOW".

1

v2x572-003

Inspection of Coolant_001

1

Reserve tank

Coolant Supply

Caution

Do not touch the radiator or coolant during
engine operation or right after the engine has
been turned off.
Due to high temperatures, doing so could
cause burns.

Caution

Supply coolant after the engine has well
cooled down.

1.

Caution

The radiator cap is pressurized.
If you remove the radiator cap while the
engine is overheated, hot steam will burst out,
possibly resulting in burns.
Make sure that the water temperature and
pressure are reduced, and then grab the cap
with a thick cloth and gradually open the cap.

Important

When you supply coolant, be sure to use
clean water, such as tap water.

Important

Tightly close the radiator cap.
If the cap is loose or incorrectly installed, the
engine will be overheated due to water
leakage, resulting in engine damage.

If the coolant level in the reserve tank is
lower than the "LOW" mark, open the
reserve tank cap and fill the tank with clean
water up to the "FULL" mark.

1

ouuoov-013

Coolant Supply_001

1

Reserve tank

If no coolant is in the reserve tank, follow
the steps below to fill the tank with clean
water.

Open the radiator cap, and then supply
clean water up to the opening.

1.

2.

[1]

Handling Instructions

GM2810A

Handling Instructions

Page 5-5

Inspection and Cleaning

Содержание GM2810A




























































































































































Отзывы:

Нет отзывов