manualshive.com logo in svg

Baroness GM2810A, Руководство по эксплуатации для владельца, Страница: 126 / 155

Поделиться
Скачать
Baroness GM2810A Скачать руководство пользователя страница 126

Adjusting the Neutral Position of the Piston

Pump

Caution

Make sure not to touch rotating tires.

Caution

When adjusting the neutral position, pay close
attention to abrupt start of the machine.
Place the jacks beneath the jack-up points,
and then lift the machine until all the tires get
off the ground.

If the machine moves forward or backward
while the traveling pedals are released, they
are not set to the neutral position.
Follow the steps below to make adjustments.

Stop the engine.
Place the jacks beneath the jack-up points,
and then lift the machine off the ground.
Make sure that no tires come into contact
with the jack stand.
Open the underseat cover.
"Opening and Closing of Underseat Cover"
(Page 5-3)
Start the engine, and rev it up to the
maximum rpm.
Set the 2WD/4WD selector switch to the
"2WD" position.
Adjust the neutral position.

If the front tires rotate forward, loosen the
lock nuts, and then turn the neutral
adjustment rod to shorten it.
If the front tires rotate in reverse, loosen
the lock nuts, and then turn the neutral
adjustment rod to extend it.

1

3

2

hsn2jo-017

Adjusting the Neutral Position of the Piston Pump_002

1.
2.

3.

4.

5.

6.

7.

[1]

[2]

1

Lock nut A (Left-hand thread)

2

Neutral adjustment rod

3

Lock nut B (Right-hand thread)

Find the position where the front wheels
stop, and then tighten the lock nuts.

Change of Fuse

Important

When performing maintenance on the
electrical system, be sure to remove the
negative battery wire.

Important

If a fuse blows, a short may have occurred
within the electrical circuit.
Check for the cause, such as faulty terminal
connections, damaged wiring or terminals, or
incorrect wiring.

Important

For fuse replacement, clean the fuse
mounting area with use of compressed air
before mounting the fuse.

Fuse Box

The fuse box includes spare fuses and tools.

1

pkm25s-010

Fuse Box_001

1

Fuse box

The machine uses a mini fuse for
automobiles.
Replace an old fuse with a new fuse of the
specified capacity.

8.

GM2810A

Repair

Page 7-4

Adjustment and Replacement

Содержание GM2810A




























































































































































Отзывы:

Нет отзывов