manualshive.com logo in svg

Baroness GM2810A, Руководство по эксплуатации для владельца, Страница: 103 / 155

Поделиться
Скачать
Baroness GM2810A Скачать руководство пользователя страница 103

Front right frame

rwyt62-008

Jack-Up Points_002

Front left frame

rwyt62-009

Jack-Up Points_003

Center of pivot

rwyt62-010

Jack-Up Points_004

Below rear wheel motors
Two locations

rwyt62-032

Jack-Up Points_005

1.

2.

3.

4.

Greasing

About Greasing

Since there may be adhesion or damage due
to lack of grease on moving parts, they must
be greased.
Add urea-based No. 2 grease in accordance
with the Maintenance Schedule.
Other locations where the specified grease or
lubricant is used are indicated in "Greasing
Points".
Add grease using the specified grease or
lubricant.

Greasing Points

Grease nipples are installed in the following
locations.
Add grease every 50 hours of operation.

4

3

8

8

2

5

1

7

1

6

3

5571D40E

Greasing Points_001

Maintenance

GM2810A

Maintenance

Page 6-3

Greasing

Содержание GM2810A




























































































































































Отзывы:

Нет отзывов