manualshive.com logo in svg

Baroness GM2810, Руководство по обслуживанию

Поделиться
Скачать
Baroness GM2810 Скачать руководство пользователя страница 84

Maintenance

About Maintenance

This chapter provides descriptions of the main
inspection and maintenance operations for the
GM2810 electrical system.
For information on daily checks, maintenance
and handling of the machine, please refer to
the separate GM2810 Owner's Operating
Manual and Parts Catalog.
For details on handling the battery, please refer
to the separate Battery Instruction Manual.

Specifications

Adjusted Value

Parking
brake switch

Slight clearance

Parking brake lever
Clearance between
the parking brake
lever and the
switch contact
point when the
brake lever at 5
notch

Proximity
sensor

Outer ends of
mower units #4/#5
400 mm (15.75 in)
from the ground up
to the outer ends of
mower units #4/#5

Proximity sensor
detection
positions : #4/#5
mower arm fulcrum
cam portions

1 - 4 mm (0.04 -
0.16 in)

Distance between
the sensors and
#4/#5 mower arm
fulcrum cam
portions

Adjustment of Safety Switch

See ( "Adjustment" (Page 5-8) ) for method
for adjustment.

GM2810

Electrical system

Page 5-2

Maintenance

Содержание GM2810


























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды