manualshive.com logo in svg

Baroness GM2810, Руководство по обслуживанию

Поделиться
Скачать
Baroness GM2810 Скачать руководство пользователя страница 107

Buzzers

Water Temperature Buzzer

The water temperature buzzer is a warning
buzzer connected to the ECU.
When a specified temperature is reached, the
ECU issues a signal, causing a buzzer to
sound (intermittent tone).
The specified temperature is 120 degrees
Celsius (120 °C).
With the circuit in this machine, the engine will
not stop even if the specified temperature is
exceeded.

1

gypyy9-009

Water Temperature Buzzer_001

1

Water Temperature Buzzer

When testing the water temperature buzzer,
disconnect the buzzer from the wiring of the
machine and test the buzzer as a single unit.
The water temperature buzzer is normal if it
emits an intermittent tone when the red wire is
connected to the positive terminal and the
black wire is connected to the negative
terminal of a 12 V battery.

1

gypyy9-010

Water Temperature Buzzer_002

1

Water Temperature Buzzer Wiring

Hydraulic Oil Level Buzzer

The hydraulic oil level buzzer is a buzzer that
warns about insufficient oil and is connected
to the level switch on the hydraulic tank.
When the hydraulic oil is less than the
specified quantity, there is continuity in the
level switch, causing a buzzer to sound
(continuous tone).

1

nzcxsv-008

Hydraulic Oil Level Buzzer_001

1

Hydraulic oil level buzzer

1

nzcxsv-002

Hydraulic Oil Level Buzzer_002

1

Level switch

Electrical system

GM2810

Electrical system

Page 5-25

Electrical components

Содержание GM2810


























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды