Baroness GM1700 Скачать руководство пользователя

Страница: 125 / 192

Removal and installation of each section

Mower unit

Removal of Mower Unit

Warning

The rotary knife is an edged tool.
Handle it carefully, since it could cut your
hands or legs.

Make sure that the parking brake is
applied.
Start the engine.
Lower the mower deck to the ground and
stop the engine.

Caution

Be sure to stop the engine before making
adjustments.

Remove the cotter pin and the pin and
then remove the lift chain.
Follow the same steps to remove them
from the other side.

3 4

2,3,4

atlwem-011

Removal of Mower Unit_001

Lift chain

Washer

Cotter pin

￭

2.
3.

Remove the clip pin and then remove the
deck tow plate from the main body.
Follow the same steps to remove them
from the other side.

atlwem-012

Removal of Mower Unit_002

Deck tow plate

Clip pin

Remove the clip pin to pull out the pin in
the direction of the arrow and then
remove the left and right front rods.

aqfz1n-009

Removal of Mower Unit_003

Clip pin

Front rod

Operating Machine and Mower Units

GM1700

Operating Machine and Mower Units

Page 7-9

Contour Deck

Содержание GM1700

































































































































































































Результаты поиска

Содержание GM1700

Отзывы:

Похожие инструкции для GM1700

Бренды по названию

Популярные бренды

Baroness GM1700, Руководство по обслуживанию

Результаты поиска

Содержание GM1700

Отзывы:

Похожие инструкции для GM1700

Бренды по названию

Популярные бренды