Baroness GM1700 Скачать руководство пользователя | Manualshive

Страница: 110 / 192

background image

Traveling rod

Adjustment of Traveling Rod

The return of the pedal neutral rod
compression spring may become insufficient
due to the usage frequency of the traveling
pedal.
Inspect them and, if necessary, implement
adjustment etc.

Follow the steps below to adjust the
traveling pedal.

Loosen the lock nut at the both ends of
the reverse rod.
Remove the bolt set securing the reverse
pedal and reverse rod.

Important

Evenly screw in the left and right screws of the
pillow ball rod end to be installed to the
reverse rod.

Adjust the length of the reverse rod so
that the reverse pedal connecting fitting
faces directly downward.

7

5

3

1

2

6

1

5

1

4

fhjgud-011

Adjustment of Traveling Rod_001

1

Bolt set (bolt, spring washer x 2, and
nut)

2

Reverse pedal connecting fitting

3

Reverse rod

4

Lock nut

5

Pillow ball rod end

6

Forward pedal

7

Forward rod

1.

[1]

[2]

[3]

Follow the same steps to adjust the forward
pedal.
The height of the position of the forward
pedal should be the same as that of the
reverse pedal.

1

2

3

fhjgud-012

Adjustment of Traveling Rod_002

1

Forward pedal

2

Reverse pedal

3

Speed adjustment screw

Important

When tightening each rod lock nut, be careful
on the position of the pillow ball rod end and
confirm that the rod moves smoothly.

Follow the steps below to adjust the
traveling rod.

The length of the neutral adjustment rod
can be adjusted just by loosening the left
and right lock nut.

1

3

4

2

jc5o3p-009

Adjustment of Traveling Rod_003

1

Forward rod

2

Reverse rod

3

Neutral adjustment rod

4

Lever adjustment bracket

2.

3.

[1]

GM1700

Main body

Page 6-6

Adjustment

«
...
108
109
110
111
112
...
»

Содержание GM1700

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GM1700

Бренд: OHIOSTEEL Страницы: 14

MULTICLIP MULTICLIP 46 S SVAN

Бренд: Stiga Страницы: 2

Бренд: Stihl Страницы: 514

Бренд: Simplicity Страницы: 48

Бренд: Qualcast Страницы: 29

EARTHWISE 60318

Бренд: ALM Страницы: 64

Бренд: Pottinger Страницы: 43

Бренд: MTD Страницы: 16

Бренд: Toro Страницы: 24

Бренд: Brill Страницы: 96

Бренд: Craftsman Страницы: 100

Бренд: Craftsman Страницы: 92

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 96

Бренд: Craftsman Страницы: 100

Бренд: Craftsman Страницы: 112

Бренд: Craftsman Страницы: 112

Бренд: Craftsman Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды