background image

23

Troubleshooting

Problem

Possible Causes

Solutions

EASYpure LF completely 

No electrical power to 

Ensure that the EASYpure LF power 

inactive. (pump not operating, 

EASYpure LF.

cord is connected to a live power

control panel not lit, etc.).

source and completely plugged into
electrical outlet.  

Make sure power entry  module switch is on.

Fuses blown.

Replace the fuses as indicated 
in the Fuse Replacement section.

Pump runs, but no display

Main PCB and display PCB 

Disconnect unit from power.

(no digital display).

not connected.

Check and reconnect boards. 

Pump does not run. Display lit.

Low water in feedwater tank 

Replenish feedwater. Check inlet 

or low inlet water pressure.

water line for constrictions, blockages
or closed valves. 

Jumper or devices not 

Install.

installed in pump interlock.

Pump worn out or defective.

Replace pump.

Display reads “Err” when

Resistivity cell lead

Check resistivity cell lead.

checking resistivity.

disconnected.

Air in system.

Purge air from system by drawing
off water according to the instructions in the

Operation section.  

Resistivity cell dirty.

Clean cell and reinstall. 

Recirculated water will not

Exhausted cartridge.

Replace the cartridges as indicated in

rinse up to desired purity level.

the Cartridge Replacement section.

Cartridges out of order.

Install the cartridges in the proper order as 
indicated In the Cartridge Installation
section.

Reduced or no product flow

0.2 micron final filter

Replace the 0.2 filter assembly as 

from the 0.2 filter assembly.

clogged.

indicated in the 0.2 Micron Filter 
Replacement section.

Cartridges improperly rinsed.

Rinse cartridges; install new filter.

Troubleshooting

Содержание EASYpure LF





































Отзывы: