Barkey warming center III DTM Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 50

Barkey warming center III DTM Скачать руководство пользователя страница 34

Service work

30

Barkey GmbH & Co. KG - Gewerbestrasse 8 - 33818 Leopoldshoehe - Germany - Head Office: +49 (5202) 9801-0

Customer Service: +49 (5202) 9801-30 Fax: +49 (5202) 9801-99 - e-mail: [email protected]

Service manual
Barkey warming center III DTM

7.6

Replacing the mechanical overtemperature protection

Removal:

►

Remove the heater insert (see Chapter 7.2).

►

Remove the cover plate (see Chapter 7.2).

►

Loosen the four heater unit screws
and pull the heater unit out towards
the front.

Figure 29: Heater unit fixing screws

►

Loosen the screw which fixes the
overtemperature protection to the
heater unit.

Figure 30: Overtemperature protection fixing screw

►

Remove the mechanical overtemperature protection from the heater unit.

►

Pull both connecting cables off the overtemperature protection.

►

Unscrew the cylindrical metal adapter from the overtemperature protection.

Refitting the overtemperature protection:

Refitting the overtemperature protection takes place in reverse order to removal:

►

Screw the cylindrical metal adapter to the overtemperature protection.

«
...
32
33
34
35
36
...
»

Содержание warming center III DTM



















































Отзывы:

Нет отзывов