Bard Site-Rite 8 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 80

Bard Site-Rite 8 Скачать руководство пользователя страница 69

Site~Rite

®

8 Ultrasound System

Page 67

17. CLEAN AND DISINFECTING THE EQUIPMENT

17.1.

Cleaning and Intermediate Disinfection Procedure using PDI® Super Sani-Cloths®

Step 1: Use one or more new towelettes to remove visible soil.

Step 2: Use two or more new towelettes to clean surfaces for at least two minutes.

Step 3 (Probe Only): Repeat Step 2 using two new towelettes for an additional two minutes.

Note:

This procedure achieves Intermediate Disinfection per the FDA guidance “Reprocessing Medical
Devices in Health Care Settings: Validation Methods and Labeling,” only when the probe is wet for a
total of four minutes and when all other surfaces are wet for a total of two minutes.

Note:

Please follow PDA® Super Saini-Cloths® instructions for use including wet time, dry time, and the use
of personal protective equipment.

Note:

If only cleaning is required, follow Steps 1 and 2.

17.2.

Additional Cleaning and Compatible Chemical Information

For a list of additional disinfectants that are chemically compatible with the Site~Rite® 8 Ultrasound System and
probe, contact Bard Access Systems for the “Site~Rite® 8 Ultrasound System Compatible Solutions” document or
call Customer Service at: 1-800-545-0890.

Caution:

Do not allow liquid to enter the system, AC adapter, connectors, or ports; damage to the equipment may
occur.

Caution:

Do not attempt to sterilize the Site~Rite® 8 Ultrasound System or probe; damage to the equipment may
occur as a result.

Caution:

Use only Bard Access System cleaning and disinfection procedures. Failure to do so may damage the
device.

Caution:

Use only approved or recommended cleaners or disinfectants to avoid damaging the equipment.

Note:

Do not spray cleaners directly onto the Site~Rite® 8 Ultrasound System display.

Note:

If disinfecting the probe with a liquid disinfectant, do not soak the probe, cable, cable bend relief, or
probe buttons.

Linear 32mm Probe

Linear 20mm Cue™ Needle

Tracking System Probe

Linear 20mm Pinpoint™ GT

Needle Technology Probe

«
...
67
68
69
70
71
...
»

Содержание Site-Rite 8

















































































Отзывы:

Нет отзывов