Barco XDL-4K75, Руководство пользователя

Страница: 8 / 117

1. Safety
To prevent personal injury
• To prevent injury and physical damage, always read this manual and all labels on the system before powering the projector or
adjusting the projector.
• Do not underestimate the weight of the projector. The projector weights ±240 kg (±529 lbs). To prevent personal injury a hoisting
tool should be used to lift the projector.
• To prevent injury, ensure that the lens, cooling system and all cover plates are correctly installed. See installation procedures.
• Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
• Warning: extremely high brightness projector : This projector embeds extremely high brightness (radiance) lasers; this laser
light is processed through the projectors optical path. Native laser light is not accessible by the end user in any use case. The
light exiting the projection lens has been defused within the optical path, representing a larger source and lower radiance value
than native laser light. Nevertheless the projected light represents a signi
fi cant risk for the human eye when exposed directly
within the beam. This risk is not speci fi c related to the characteristics of laser light but solely to the high thermal induced energy
of the light source; which is comparable with lamp based systems.
Thermal retinal eye injury is possible when exposed within the Hazard Distance. The Hazard Distance (HD) is de
fi ned from
the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible
exposure as described in the chapter "High Brightness precautions: Hazard Distance (HD)", page 7.
• Based on international requirements, no person in allowed to enter the projected beam within the zone between the projection
lens and the related Hazard Distance (HD). This shall be physically impossible by creating suf
fi cient separation height or by
placing optional barriers. Within the restricted area operator training is considered suf fi cient. The applicable separation heights
are discussed in "High Brightness precautions: Hazard Distance (HD)", page 7.
• The projector shall be installed in a restricted access room equipped with a key or security lock preventing untrained persons
entering the Class 4 use zone.
• Before attempting to remove any of the projector’s covers, disconnect the projector power cable from the mains electricity for
removal of all power from the projector.
• When required to remove all power from the projector (e.g. during service), always disconnect the power from the projector
mains terminals and UPS INLET connector. Use the disconnect device in the building installation to disconnect the power to
the projector mains terminals, and unplug the power cord at the UPS INLET connector if the UPS INLET is separately powered.
• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and
possible injury to the user.
• Lenses, shields or screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is
impaired. For example by cracks or deep scratches.
• The associated Laser Safety responsible of the unit must evaluate the setup before the unit may be started.
• Never point or allow light to be directed on people or re fl ective objects within the HD zone.
• If the unit is shut down, remove the key control from the system; avoiding unauthorized startup.
• All operators shall have received adequate training and be aware of the potential hazards.
• Strictly minimize the number of people who have access to the unit. The unit may never be operated without permission of the
responsible for laser safety.
• When the projected light causes a dangerous situation the operator must hit the beam stop button which is located close to the
control panel. The beam stop removes all power from the laser power supplies.
• Don’t put your hand in front of the beam.
• Do not clean the port window when the projector is switched on.
• Position the hoses of the cooling system so that they will not be tripped over, pulled, or contact hot surfaces.
To prevent battery explosion
• Danger of explosion if battery is incorrectly installed.
• Replace only with the same or equivalent type recommended by the manufacturer.
• For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations
to ensure proper disposal.
4 R5906151 XDL 17/04/2018