Barco RLM G5i Performer R9010320 Скачать руководство пользователя

Страница: 102 / 150

11. Lamps Menu

11.3 Mode

Single lamp mode

The projector will always switch to the lamp with the shortest runtime when the difference between the runtimes of lamp 1 and lamp
2 reaches

100 hours

, switching from one lamp to another happens only at switching on of the projector and not during operation.

When the lamp fails or reaches its maximum runtime the projector switches automatically to the other lamp without interrupting the
projection. The failure is logged and the lamp will never be initialized in the future.

Image 11-3
Single mode operation: switching principle

Dual lamp mode

Both lamps are working.

When one lamp fails, the projector continues the projection using the remaining lamp.

How to select the lamp mode ?

1. Press

MENU

to activate the menu bar.

2. Press

→

to select the

Lamps

item. (image 11-4)

3. Press

↓

to pull down the

Lamps

menu.

4. Use

↑

↓

to select

Mode.

5. Press

→

to pull down the menu.

6. Use

↑

↓

to select the desired mode.

Single

Only one lamp is ignited.

Dual

Both lamps are ignited.

7. Press

ENTER

to confirm.

A bullet shows the active mode.

100

R5976815 RLM G5I PERFORMER 02/06/2006

Содержание RLM G5i Performer R9010320























































































































































Результаты поиска

Содержание RLM G5i Performer R9010320

Отзывы:

Похожие инструкции для RLM G5i Performer R9010320

Бренды по названию

Популярные бренды

Barco RLM G5i Performer R9010320, Руководство пользователя

Результаты поиска

Содержание RLM G5i Performer R9010320

Отзывы:

Похожие инструкции для RLM G5i Performer R9010320

Бренды по названию

Популярные бренды