Barco HDF W series Скачать руководство пользователя

Страница: 89 / 319

8. Input

Image 8-43
EDID selection list

Use the

▲

▼

key to select the input to con

gure.

Press

ENTER

to open the selection list.

The current active

le is checked.

Use the

▲

▼

key to select the correct

le.

Press

ENTER

to select this

le.

Press

EXIT

to return to the

EDID Con

guration

menu.

Use the

▲

▼

key to select

Apply

Your selection is applied and stored for this input.

The

EDID Con

guration

menu remains open to con

gure another input.

Or,
use the

▲

▼

key to select

Your selection is applied and stored for this input and the

EDID con

guration

menu is closed.

8.8.2

Create custom EDID

Description

You can create new custom EDID

les and enter the desired input timings.

How to create

Press

Menu

to activate the menus and select

Input

→

EDID

→

Create

Press

ENTER

to open the EDID creation menu.

Image 8-44
Main menu

Image 8-45
Input, EDID

R5905158 HDF SERIES 16/06/2015

Содержание HDF W series
































































































































































































































































































































Результаты поиска

Содержание HDF W series

Отзывы:

Похожие инструкции для HDF W series

Бренды по названию

Популярные бренды

Barco HDF W series, Инструкция по использованию и установке

Результаты поиска

Содержание HDF W series

Отзывы:

Похожие инструкции для HDF W series

Бренды по названию

Популярные бренды