Barco FLM series Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 331

Barco FLM series Скачать руководство пользователя страница 134

14. Lens holder

14.2 Installing the lens holder

Necessary tools

•

5,5 mm nut driver.

•

3 mm Allen key.

Necessary parts

Two cable ties.

How to install the lens holder ?

1. Release the two screws (C), which fasten the mid position switch (S) to the projector chassis and position the switch as illustrated.

Use a 5,5 mm nut driver.

Note:

The mid position switch has to be removed otherwise the switch may damaged while installing the lens holder.

S

C

C

Image 14-5

2. Install the lens holder and secure with 8 hexagon socket screws (F) as illustrated. Use a 3 mm Allen key.

Note:

Ensure that the positioning pins of the lens holder matches the positioning holes on the projector chassis.

F

Image 14-6

3. Remove the front plate of the lens holder by releasing the three retainer screws (D) and the three fixation screws (E). Use a 3

mm Allen key.

Note:

There is a wire unit attached to the front plate and lens holder. So, you won’t be able to remove the front plate but just
shift it a little to the left to gain access to the fixation screws of the mid position switch.

132

R59770072 FLM SERIES 19/03/2007

«
...
132
133
134
135
136
...
»

Содержание FLM series












































































































































































































































































































































Отзывы:

Нет отзывов