R5909934 /00
E2 Lite and EC-40
180
Image 7-3: Adjust MVR panel
—
Connector
7.13 Configuration Menu > Add Screen
Destinations & Layers
General
In this procedure, you will Add Screen Destinations from the defined outputs.
Prerequisite
•
Ensure that you are familiar with the
Configuration Menu
. For details on this menu, please refer to
chapter
, page 71
If more than one Destination is utilized, repeat the below steps until all Destinations are added.
Add Screen Destinations
1.
Click on the
Destination
tab to define destinations for the defined outputs.
2.
From the diagram area click on the output that you want to be part of the destination. If no connector is
selected the first available connector will be selected.
3.
Click on the
+Add Screen Destination
blue button to assign the output to the screen destination.
4.
When the destination is created a box appears next to the unit diagram.
5.
If there is more than one output part of the destination, for a widescreen for instance, drag and drop these
outputs into the destination box. You will observe that the destination size automatically updates as new
outputs are added to the destination.
An EMP allows only a certain mix of Screen (Program) Destinations and AUX Destinations. Each
card can support up to four (4) Screen Destinations (Program Outputs), or up to four (4) AUX
outputs, or two (2) AUX and two (2) Screen Outputs. All Outputs can be AUX Destinations, and all
Outputs can be assigned to Screen Destinations. Screen Destination sizes are determined by the
available amount of pixel canvas, not by the number of Outputs assigned to a Screen Destination.
Add Layers to Destinations
Click on the
Adjust
tab that is located on the top.
1.
Under the
Assign
sub-menu click on the
+Assign Layer to Destinatio
n blue button.
2.
Click on this button as many times is required to add the layers you are assigning to the destination. Observe
the number of layers indicated in the Layer box is incremented every time the add button is pressed. See also
Configuration Menu > Layer optimization
”
Содержание Event Master E2 Lite
