Barco DP2K-E series Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 163

background image

11. Scheimpflug

11. SCHEIMPFLUG

About this chapter

This chapter explains the Scheimp

fl

ug principle and when to apply Scheimp

fl

ug correction upon your DP2K-E series projector. In

addition to the procedure for Scheimp

fl

ug adjustment the procedure to adjust the Back Focal Length is also included in this chapter.

Scheimp

fl

ug principle

The "plane of sharp focus" can be changed so that any plane can be brought into sharp focus. When the DMD plane
and lens plane are parallel, the plane of sharp focus will also be parallel to these two planes. If, however, the lens
plane is tilted with respect to the DMD plane, the plane of sharp focus will also be tilted according to geometrical and
optical properties. The DMD plane, the principal lens plane and the sharp focus plane will intersect in a line below the
projector for downward lens tilt.

Overview

•

ug introduction

•

•

Fixation of the Lens Holder front plate

•

Back Focal Length adjustment

R5906693 DP2K-E SERIES 19/06/2015

79

«
...
81
82
83
84
85
...
»

Содержание DP2K-E series




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DP2K-E series

Бренд: NEC Страницы: 159

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 2

Бренд: Panamax Страницы: 3

Бренд: CAPTELEC Страницы: 10

Бренд: InFocus Страницы: 2

POCKETBEAM TOUCH 2

Бренд: Merlin Страницы: 4

Бренд: Reer Страницы: 44

Optoma ZU510T-W

Бренд: Optoma Страницы: 49

Бренд: Casio Страницы: 72

Бренд: Epson Страницы: 24

ELP-5500 - PowerLite 5500C SVGA LCD Projector

Бренд: Epson Страницы: 2

EMP 30 - PowerLite 50c XGA LCD Projector

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 32

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 3

Бренд: Epson Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды