Barco DP2K-E series Скачать руководство пользователя страница 81

Страница: 81 / 163

10. Starting up

10.2 Switching the DP2K-E series projector OFF

How to switch the DP2K-E series projector OFF?

1. Press the Standby button on the Local Keypad or use the Communicator Touch Panel to switch the projector from Lamp ON

mode to Standby mode. As a result the lamp turns off while the fans keep turning to cool down the projector.

2. Allow the projector to cool down for 5 minutes minimum or until the speed of the fans decreases.

3. Switch the projector OFF with the power switch.

Tip:

Make sure no lens motors are running while switching off the projector. Wait for lens positioning to complete.

5min

Image 10-2

How to put the projector into Sleep mode?

1. Check if the lamp is switched off. If not, press the Standby button on the Local Keypad or use the Communicator to switch the

lamp off. The backlight color of the Standby button is red when the lamp is switched off.

Note:

To put the projector into Sleep the projector must be in Standby mode (in other words the lamp must be off). If the lamp
is ignited he Sleep button is disabled notwithstanding the backlight color of the Sleep button is green.

2. Press the

SLEEP

button on the Local Keypad for three seconds or use the Communicator to put the projector into Sleep mode.

As a result the projector immediately shuts down the electronics but when the lamp is still too hot the projector will

nish the after

cooling cycle and then

nally go to sleep. The backlight color of the Sleep button is white in Sleep mode even when the projector

nishing the after cooling cycle.

Note:

Pressing the Sleep button before the after cooling cycle has

nished, will re-start the projector in a normal way.

R5906693 DP2K-E SERIES 19/06/2015

Содержание DP2K-E series




































































































































































Результаты поиска

Содержание DP2K-E series

Отзывы:

Barco DP2K-E series, Руководство пользователя и инструкция по установке, Страница: 81 / 163

Результаты поиска

Содержание DP2K-E series

Отзывы: