Barco DP2K-E series Скачать руководство пользователя

Страница: 70 / 163

8. ICMP

8.11 Installing a HDD into the ICMP

This procedure assumes that the HDD slot of the ICMP is empty. If not, see procedure "Removing a HDD form
the ICMP", page 65.

AUTION

Always use a new empty spare part HDD from Barco to replace a malfunction HDD. Do not use a

HDD from another ICMP HDD set.

AUTION

Always make sure that all HDDs in the ICMP HDD set have the same storage capacity. See label

on top of the HDD to know the storage capacity.

How to install a HDD ?

1. Ensure that the projector is switched off.

2. Prepare the HDD for insertion by moving the latch towards the left and push the unlock button to open the handle.

Image 8-15

3. Insert the HDD into the HDD slot. Ensure that the handle is suf

ciently open so that the hook (reference 1) of the handle can

pass the front plate of the ICMP.

Image 8-16

4. Push the HDD completely and

rmly inside its slot, close the handle, and move the latch towards the right.

R5906693 DP2K-E SERIES 19/06/2015

Содержание DP2K-E series




































































































































































Результаты поиска

Содержание DP2K-E series

Отзывы:

Похожие инструкции для DP2K-E series

Бренды по названию

Популярные бренды

Barco DP2K-E series, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание DP2K-E series

Отзывы:

Похожие инструкции для DP2K-E series

Бренды по названию

Популярные бренды