Barco DP-1200 Скачать руководство пользователя

Страница: 76 / 134

8. Starting up

8.1

Switching ON the DP-1200 digital projector

How to switch ON the DP-1200 digital projector?

1. Make sure that the DP-1200 projector is installed upon a stable pedestal. See chapter "Positioning the DP-1200 at port window",

page 18.

2. Make sure that the exhaust system is properly installed. See chapter "Installation of the exhaust system", page 21.

3. Make sure that the right lens is installed for your application. See chapter "Lens selection", page 47.

4. Make sure that the lamp and lamp house are correctly installed. See chapter "Lamp & Lamp House", page 27.

5. Make sure the projector is correctly connected to the power net. See chapter "Connecting the projector with the power net", page

22.

6. Check if a video source is connected with the projector. See chapter "Source input ports of the DP-1200 projector", page 64.

7. Check if the communicator touch panel is installed. See chapter "Communicator touch panel", page 65.

8. Press the power switch to switch ON the projector. As a result the projector starts up in standby. So, the lamp is OFF and the

dowser closed. No internal pattern is selected. The communicator touch panel starts its initialization procedure.
-

When ’0’ is visible, the projector is switched OFF.

When ’1’ is visible, the projector is switched ON.

9. Press the standby button on the local keypad or use the Communicator Touch Panel to activate the lamp.

10.Press the “DOWSER” button on the local keypad or use the Communicator Touch Panel to open the dowser. As a result the

applied source will be displayed.

AUTION

See user’s guide of the Communicator Touch Panel to operate and control the DP-1200 projector.

R59770242 DP-1200 06/01/2009

Содержание DP-1200







































































































































Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды

Barco DP-1200, Руководство по установке

Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды