Barco DP-1200 Скачать руководство пользователя

Страница: 46 / 134

4. Lamp & Lamp House

4.6

Resetting the lamp parameters

AUTION

The “LAMP INFO” parameters which are stored on a chip MUST be updated after each installation

of an xenon bulb lamp inside the lamp house. Neglecting this update will result in poor performance and short
life time of the xenon bulb lamp.

How to reset the lamp parameters?

1. Start up the projector but do not ignite the lamp.

2. Go via the

Communicator

touch panel to the menu “

Installation

” > “

Lamp

” > “

Lamp information

”.

3. While the

Lamp information

window is displayed, tip on

Reset

(1).

A reset message is displayed (2).

4. Fill out the article number of the new lamp (3a)

Or,
click on

Select

(3b) to display a list of possible article numbers (4). Select a article number (5) and click

(6).

The software will check if the entered article number is a valid number (7).

5. Fill out the serial number of the lamp (8).

6. Click

Reset

(9).

Image 4-22
Reset lamp info

AUTION

For more information about using the Communicator touch panel consult the user’s guide of the

communicator touch panel.

R59770242 DP-1200 06/01/2009

Содержание DP-1200







































































































































Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды

Barco DP-1200, Руководство по установке

Результаты поиска

Содержание DP-1200

Отзывы:

Похожие инструкции для DP-1200

Бренды по названию

Популярные бренды