Barco BarcoReality 909 Split Pack R9040040, Руководство пользователя

Страница: 21 / 111

4. Getting Started
14 TEXT when adjusting one of the image, e.g. controls during a meeting, the displayed bar scale
can be removed by pressing ’TEXT’ key first. To re-display the bar scale on the screen,
press ’TEXT’ key again.
15 ENTER to start up the adjustment mode or to confirm an adjustment or selection in the adjustment
mode.
16 Cursor keys to make menu selections when in the adjustment mode or to zoom/focus when the direct
access is active.
Comparison between the cursor keys and the use of the ’+’ and ’-’ keys on the local keypad
: RCU = local keypad
cursor key up = ’+’ key up
cursor key down = ’-’ key down
cursor key right = ’+’ key right
cursor key left = ’-’ key left
17 EXIT to leave the adjustment mode or to scroll upwards when in the adjustment mode.
18
RC operation indication lights up when a button on the remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
Table 4-1
4.4 Switching on the projector
How to switch on the projector?
1. Press the mains ON/OFF switch to switch on the projector.
Pressed
ON
Not Pressed OFF
Table 4-2
Mains Power Switch
POWER MAINS
COMM. PORT
REMOTE RE
MOTE
IRIR
RS 232 OUT RS 232 O
UT
RS 232 IN
R G B
Comp / H-Sync V-Sync
R G B
Co mp / H-S ync
DEFOCUS
DEFO CUS
75 Ohm
OFF - ON
75 Oh m
ON - OFF
75 Ohm
OFF - ON
75 Oh m
ON - OFF
red: standby
green: operation
re d: s ta ndby
gre en : ope ra tion
X-POS Y-POS
X-POS Y-POS
V-Syn c
RS 232 IN
COMM. P ORT PORT 3
PORT 4 / 5
PORT 4 / 5
PORT 2
PORT 2
PROJECTOR MODE
PRO JEC TO R MO DE
PORT 1
ON OFF
ON OFF
POWER MAINS
800 periphals
800 peri ph als
This device complies with part 15 of the FCC rules.
Operation is subject to following two conditions (1).
This device may not cause harmful interference,
and (2) this device must accept any interference that
may cause undesired operation.
See installation instructions before connecting to the supply.
Voir la notice d' installation avont de raccorder au r éseau.
See i nst alla tion i nst ruc tions before c onnecting to the s upply.
Voi r la notice d' ins tal lati on avont de r acc order au r éseau.
Thi s dev ice c om plie s wi th part 15 of the F CC rul es.
Oper ation i s s ubjec t to follo wing two c onditions (1) .
Thi s dev ice m ay not c ause har mful inter fer ence,
and (2) this dev ice m ust accept any inter fer ence that
may caus e undesir ed operati on.
PORT 3 PORT 1
Image 4-2
The Stand by indication lamp will show the status of the projector:
No light up Switched OFF
Green color Operational mode
Red color Stand By mode
Table 4-3
Status lamp
The switching on modes
When switching on with the power switch, the projector can start in 2 different modes depending on the “Power Up” setting in the
Service mode:
•
Operational mode (Picture displayed).
• Stand By mode.
Starting up in Operational Mode
The projector can start up with the selected source or the projector can start up with a warm up cycle message.
R5976398 BARCOREALITY 909 SPLIT PACK 21/02/2003 17