Barco Athena Скачать руководство пользователя

Страница: 62 / 74

7. Starting up

When for any reason a restart of the projector is required, the content server should be restarted also.

7.2

Switching the Athena OFF

How to switch the Athena OFF?

1. Press the Standby button on the Local Keypad or use the Communicator Touch Panel to switch the projector from Lamp ON

mode to Standby mode. As a result the lamp turns off while the fans keep turning to cool down the projector.

2. Allow the projector to cool down for 5 minutes minimum or until the speed of the fans decreases.

3. Switch the projector OFF with the power switch.

Tip:

Make sure no lens motors are running while switching off the projector. Wait for lens positioning to complete.

5min

Image 7-2

How to put the projector into Sleep mode?

1. Check if the lamp is switched off. If not, press the Standby button on the Local Keypad or use the Communicator to switch the

lamp off. The backlight color of the Standby button is red when the lamp is switched off.

Note:

To put the projector into Sleep the projector must be in Standby mode (in other words the lamp must be off). If the lamp
is ignited he Sleep button is disabled notwithstanding the backlight color of the Sleep button is green.

2. Press the

SLEEP

button on the Local Keypad for three seconds or use the Communicator to put the projector into Sleep mode.

As a result the projector immediately shuts down the electronics but when the lamp is still too hot the projector will

nish the after

cooling cycle and then

nally go to sleep. The backlight color of the Sleep button is white in Sleep mode even when the projector

nishing the after cooling cycle.

Note:

Pressing the Sleep button before the after cooling cycle has

nished, will re-start the projector in a normal way.

R5906789 ATHENA 16/12/2016

Содержание Athena











































































Результаты поиска

Содержание Athena

Отзывы:

Похожие инструкции для Athena

Бренды по названию

Популярные бренды

Barco Athena, Руководство пользователя

Результаты поиска

Содержание Athena

Отзывы:

Похожие инструкции для Athena

Бренды по названию

Популярные бренды