background image

10

Warranty Terms

To make a claim under the warranty, it is important to register the Barbas appliance after purchase
via www.barbasbellfires.com.

Barbas Bellfires Warranty Terms

Barbas Bellfires B.V. guarantees the quality of the supplied Barbas appliance and the
quality of the materials used. All Barbas appliances are developed and manufactured
according to the highest possible quality standards. If, despite all this, something should
prove amiss with the Barbas appliance you have purchased, Barbas Bellfires B.V. offers
the following manufacturer’s warranty.

Article 1: Warranty

1.

If Barbas Bellfires B.V. determines that the Barbas appliance you have purchased is
defective as a result of a flaw in the construction or material, Barbas Bellfires
B.V.guarantees to repair or replace the appliance free of charge, without charging
any costs for labor or spare parts.

2.

Repair or replacement of the Barbas appliance will be undertaken by Barbas Bellfires
B.V.or by a Barbas dealer as designated by Barbas Bellfires B.V.

3.

This warranty is supplementary to the existing legal national warranty of Barbas
dealers and Barbas Bellfires B.V. in the country of purchase and is not intended to
restrict your rights and claims based on the applicable legal provisions.

Article 2: Warranty conditions

1.

Should you wish to claim under the warranty, please contact your Barbas dealer.

2.

Complaints should be reported as quickly as possible after they have manifested
themselves.

3.

Complaints will only be accepted if they are reported to the Barbas dealer,together
with the serial number of the Barbas appliance which is stated on the enclosed
documents.

4.

In addition, the original receipt (invoice, receipt, cash receipt) showing the date of
purchase must also be submitted.

5.

Repairs and replacements during the warranty period do not give any entitlement to
an extension of the warranty period. After a repair or replacement of warranty parts,
the warranty period shall be deemed to have started on the date of purchasing the
Barbas appliance.

6.

If a certain part is eligible for the warranty and the original part is no longer available,
Barbas Bellfires B.V. shall ensure that an alternative part of at least the same quality
shall be provided.

Article 3: Warranty exclusions

1.

The warranty on the Barbas appliance ceases to be in effect if:

a.

it is not installed according to the installation instructions, and to national and/or
local regulations;

b.

it has been installed, connected or repaired by a non-Barbas dealer;

c.

it has not be used or maintained according to the instructions for use;

Warranty Terms

80

Gas Fire Front 70-60

Содержание Gas Fire Front 70-60 PF2





















































































Отзывы: